Código estación metereológica

  #InnovaEx20_21

Una vez que hemos consiguido que funcione nuestra placa, os dejo el programa por el que por fín estamos recogiendo los datos de nuestra estación metereológica:

/*

 Weather Shield Example

 By: Nathan Seidle

 SparkFun Electronics

 Date: June 10th, 2016

 License: This code is public domain but you buy me a beer if you use this and we meet someday (Beerware license).

 This example prints the current humidity, air pressure, temperature and light levels.

 The weather shield is capable of a lot. Be sure to checkout the other more advanced examples for creating

 your own weather station.

 Updated by Joel Bartlett

 03/02/2017

 Removed HTU21D code and replaced with Si7021

 */

#include <Wire.h> //I2C needed for sensors

#include "SparkFunMPL3115A2.h" //Pressure sensor - Search "SparkFun MPL3115" and install from Library Manager

#include "SparkFun_Si7021_Breakout_Library.h" //Humidity sensor - Search "SparkFun Si7021" and install from Library Manager

MPL3115A2 myPressure; //Create an instance of the pressure sensor

Weather myHumidity;//Create an instance of the humidity sensor

//Hardware pin definitions

//-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

const byte STAT_BLUE = 7;

const byte STAT_GREEN = 8;

const byte REFERENCE_3V3 = A3;

const byte LIGHT = A1;

const byte BATT = A2;

//Global Variables

//-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

long lastSecond; //The millis counter to see when a second rolls by

void setup()

{

  Serial.begin(9600);

  Serial.println("Weather Shield Example");

  pinMode(STAT_BLUE, OUTPUT); //Status LED Blue

  pinMode(STAT_GREEN, OUTPUT); //Status LED Green

  pinMode(REFERENCE_3V3, INPUT);

  pinMode(LIGHT, INPUT);

  //Configure the pressure sensor

  myPressure.begin(); // Get sensor online

  myPressure.setModeBarometer(); // Measure pressure in Pascals from 20 to 110 kPa

  myPressure.setOversampleRate(7); // Set Oversample to the recommended 128

  myPressure.enableEventFlags(); // Enable all three pressure and temp event flags

  //Configure the humidity sensor

  myHumidity.begin();

  lastSecond = millis();

  Serial.println("Weather Shield online!");

}

void loop()

{

  //Print readings every second

  if (millis() - lastSecond >= 1000)

  {

    digitalWrite(STAT_BLUE, HIGH); //Blink stat LED

    lastSecond += 1000;

    //Check Humidity Sensor

    float humidity = myHumidity.getRH();

    if (humidity == 998) //Humidty sensor failed to respond

    {

      Serial.println("I2C communication to sensors is not working. Check solder connections.");

      //Try re-initializing the I2C comm and the sensors

      myPressure.begin(); 

      myPressure.setModeBarometer();

      myPressure.setOversampleRate(7);

      myPressure.enableEventFlags();

      myHumidity.begin();

    }

    else

    {

      Serial.print("Humidity = ");

      Serial.print(humidity);

      Serial.print("%,");

      float temp_h = myHumidity.getTempF();

      Serial.print(" temp_h = ");

      Serial.print(temp_h, 2);

      Serial.print("F,");

      //Check Pressure Sensor

      float pressure = myPressure.readPressure();

      Serial.print(" Pressure = ");

      Serial.print(pressure);

      Serial.print("Pa,");

      //Check tempf from pressure sensor

      float tempf = myPressure.readTempF();

      Serial.print(" temp_p = ");

      Serial.print(tempf, 2);

      Serial.print("F,");

      //Check light sensor

      float light_lvl = get_light_level();

      Serial.print(" light_lvl = ");

      Serial.print(light_lvl);

      Serial.print("V,");

      //Check batt level

      float batt_lvl = get_battery_level();

      Serial.print(" VinPin = ");

      Serial.print(batt_lvl);

      Serial.print("V");

      Serial.println();

    }

    digitalWrite(STAT_BLUE, LOW); //Turn off stat LED

  }

  delay(100);

}

//Returns the voltage of the light sensor based on the 3.3V rail

//This allows us to ignore what VCC might be (an Arduino plugged into USB has VCC of 4.5 to 5.2V)

float get_light_level()

{

  float operatingVoltage = analogRead(REFERENCE_3V3);

  float lightSensor = analogRead(LIGHT);

  operatingVoltage = 3.3 / operatingVoltage; //The reference voltage is 3.3V

  lightSensor = operatingVoltage * lightSensor;

  return (lightSensor);

}

//Returns the voltage of the raw pin based on the 3.3V rail

//This allows us to ignore what VCC might be (an Arduino plugged into USB has VCC of 4.5 to 5.2V)

//Battery level is connected to the RAW pin on Arduino and is fed through two 5% resistors:

//3.9K on the high side (R1), and 1K on the low side (R2)

float get_battery_level()

{

  float operatingVoltage = analogRead(REFERENCE_3V3);

  float rawVoltage = analogRead(BATT);

  operatingVoltage = 3.30 / operatingVoltage; //The reference voltage is 3.3V

  rawVoltage = operatingVoltage * rawVoltage; //Convert the 0 to 1023 int to actual voltage on BATT pin

  rawVoltage *= 4.90; //(3.9k+1k)/1k - multiple BATT voltage by the voltage divider to get actual system voltage

  return (rawVoltage);

}